PLUMBING 101: TIPS FOR INSTALLING A BATHTUB

Plumbing 101: Tips for Installing a Bathtub

Plumbing 101: Tips for Installing a Bathtub

Blog Article

Contact Us Now

The publisher is making several great annotation about How to Install a Bathtub in general in this post further down.


Installing A Bathtub
Mounting a bath tub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard job. If the old tub is easily available, the project can move immediately; if you have to open up a wall surface to remove the old bathtub and position the new tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will require an assistant to vacate the old tub as well as embeded in the brand-new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Rather than working with a professional to take control of a halfway-completed task, it is far better to consider utilizing one before you begin. Possibilities are you might need a professional plumber to make tube connections.
This article will assist you set up a new bathtub in your restroom if you have actually currently bought a brand-new tub as well as do not require to transform the setup of your previous water pipes.
Your tools and also material checklist must consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you require to change old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is typically the case.
    Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. Once the supply pipes have been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing substance.
    Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the various other end offers a link to the current supply pipes.
    If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the mounting opening in the bath/basin guaranteeing that the washers remain in area between the tap as well as the sink. Safeguard the tap in position with the maker provided backnut. When the faucet is firmly in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Setting up the Tub


    Utilizing the two wood boards under its feet, position the bath tub in the required placement. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
    The following objective is to make certain that the tub is leveled all round. This can be achieved by checking the level and changing the feet on the bath tub up until the level checks out degree.
    To set up faucets, fit the bottom of the furthest adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
    Activate the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub and additionally check the overflow electrical outlet as well as the typical outlet for leaks.
    Ultimately, deal with the bath paneling as defined in the supplier's user's manual. Tiling and also sealing around the tub needs to wait till the tub has been made use of at the very least when as this will settle it into its last setting.

    Getting ready for the Installment


    Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to prevent stress on the tub.
    Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you make use of every one of the supplied washers.
    Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last position.

    Tiling Around the Tub


    In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
    You can select from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can split relatively early if you do not consider this motion before sealing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is advisable to fit the floor tiles using waterproof or waterproof adhesive and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    We had been shown that article on Tools You Need to Install a New Bathtub from an acquaintance on a different web blog. Those who enjoyed our blog entry kindly do not forget to pass it around. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Visit Link

    Report this page